(800) 622-0828 (US, CA)
(325) 235-5494
(325) 235-4672

To search products by model number, enter "m..."
(Ex: Enter "m3" to search for Model 3.)

Health Physics Medical Physics Metal Recycling Monitoring Systems Emergency Response

Metal Recycling

Extended Reach microR / microSv Meters

No subcategories

Need Help?

Unsure about which instrument is best for your application?

Find your region's Ludlum representative or dealer.

Contact Ludlum Sales:

(800) 622-0828 (USA Toll Free)

(325) 235-5494

Model 3019

Digital microR Survey Meter

Part Number: 48-4091

Features

Very Sensitive Internal CsI Detector
Large, Backlit, Easy-To-Read LCD Screen
Auto-Ranging
Rate, Max, and Count Modes
Sigma Audio Mode
Splash-Resistant Construction for Outdoor Use
All Digital Calibration
Lightweight yet Rugged
Simple 5-Button Interface

The Model 3019 is a portable and versatile instrument with an internal detector used for background measurements of gamma radiation levels up to 500 µSv/h (50 mR/hr). The internal CsI scintillation detector has a sensitivity of 175 cpm per µR/hr. It features a large, easy-to-read LCD screen and audible alarms and is controlled using a simple five-button interface. The meter body is made of high-impact plastic and splash resistant construction allows the instrument to be used outdoors.

Three modes of operation are available - RATE, MAX, and COUNT - which can be selected by pressing the MODE button. Measurements can be collected in two sets of units (primary and secondary) for RATE and MAX modes in cps, cpm, mR/h, or µSv/h units. The user can switch between the two sets of units by pressing the UNITS button. A sigma audio mode can be enabled that allows the user to find small increases above the background radiation level. When enabled with the optional Lumic Data Logger Kit (see Options), data can be logged in any of the operational modes using the LOG button on the handle. Up to 1000 data points can be stored internally.

Instrument setup can be done either through the front-panel controls or via the Lumic Calibration Kit (see Options). The Model 3019 is shipped ready to use with batteries and calibration certificate.

Note: While the detector used in this instrument is sensitive and is often used for detection of near-background levels of radiation, its nonlinear energy response means that dose and exposure measurements may be over/underreported. (See graph below.)

Specifications

Detector (D x L)	Internal CsI scintillator, 2.5 x 1.9 cm (1 x 0.75 in.)
Sensitivity	175 cpm per µR/hr
Energy Range	Nonlinear (see Energy Response Curve in the Graphs tab)
Linearity	Reading within 10% of true value
Display	3 digit LCD with large 20 mm (0.8 in.) digits. Units: (k)cps, (k)cpm, (µ)(m)R(/h), (µ)(m)Sv(/h) Indicators: bar graph, MAX, ALARM, USB, audio, low-battery.
Detector Range	Background to 500 µSv/h (50 mR/hr)
Backlight	Built-in ambient light sensor automatically activates low-power LED backlight, unless internal dipswitch is set to continuous-On (will reduce battery life)
User Controls	ON/OFF: Extra-long press to turn ON; short press to acknowledge alarms; extra-long press plus 3 seconds to turn OFF UNITS: Short press changes the units between count rate, dose/exposure, or disintegration, an extra-long press to change count time in COUNT mode AUDIO: Short press to adjust audio level MODE: Short press alternates between modes: RATE (displays count rate), MAX (captures peak rate), and COUNT (captures rate or dose readings for a user-selectable preset count time from 0 to 10 min.) LOG: Short press to log current display (requires Lumic Data Logger Kit, see Options) or initiate count in COUNT mode
Data Logging	Can store up to 1000 data points internally. Requires Lumic Data Logger Kit (see Options).
Response Time	User-selectable from 1 to 60 seconds, or Auto-Response Rate FAST or SLOW
Alarms	Two adjustable count rate, exposure/dose, and count alarm setpoints adjustable over the display range (see manual)
Sigma Audio Mode	Alarm that allows user to find small increases above the background radiation level. The instrument will beep whenever it measures a rate that exceeds a threshold rate above the measured background rate.
Overload Protection	High count rate saturation protection prevents false display of lower count rates. "OL" will appear on the display and an audio warning will be triggered.
Loss of Count Protection	After a user-settable time interval (default of 60 seconds) of no pulses from the detector, unit will flash a zero reading and the alarm audio will be triggered
Dead Time Correction	Employs first and second order corrections for extended performance
Overrange	If the reading should exceed the predefined detector range, the instrument will flash a maximum reading and trigger an audio warning.
High Voltage	400 to 1500 Vdc
Threshold	-20 to -100 mVdc
Audio	Approximately 4.5 kHz, click audio greater than 65 dB at 0.6 m (2 ft), alarm audio greater than 72 dB
Power	Four alkaline“AA” batteries
Battery Life	Approximately 750 hours of operation (as low as 100 hours with backlight configured for continuous-on), 16-hour low battery warning
Construction	High-impact plastic with water-resistant rubber seals and separate battery compartment
Temperature Range	-20 to 50 °C (-5 to 122 °F) May be certified for operation from -40 to 65 °C (-40 to 150 °F)
Enviornmental Rating	NEMA rating of 5 or IP rating of 53
Size (H x W x L)	16.5 x 11.4 x 21.6 cm (6.5 x 4.5 x 8.5 in.)
Weight	1.06 kg (2.3 lb)

Options

Option	Description	Part Number
Lumic Calibration Kit	Lumic Calibration Software allows the reading and writing of important parameters via a USB port in the Model 3000 Series and Model 30 family of instruments. This software also includes a calibration wizard (guides the user through calibration steps) and a plateau wizard (determines the optimal detector operating voltage). The kit includes Lumic Calibration Software versions 1.0 and 2.0, a Model 3000 Series USB cable, and a Model 30 family USB cable.	4519-865
Lumic Configuration Kit	Lumic Configuration Software allows the reading and writing of important parameters via a USB port in the Model 3000 Series and Model 30 family of instruments. Does not include calibration or plateau wizards. The kit includes the Lumic Configuration Software, a Model 3000 Series USB cable, and a Model 30 family USB cable.	4519-747
Lumic Data Logger Kit (Model 3000-Series)	Includes Lumic Data Logger Software and cable.	4498-1019
Headphone Jack	Adds a headphone jack to the instrument.	4498-555
Stereo/Mono Headphones	Adjustable stereo/mono headphones.	22-9313
Shoulder Strap	1.8 m (6 ft) adjustable nylon shoulder strap. Requires instrument case modification.	4498-868
Model 3000-Series Case	Rugged, dust- and waterproof transport and storage case.	2312958

Firmware Updates

In order to use the latest Lumic Calibration Software*, you may need to update the firmware on your instrument. (All new instruments will be compatible with the latest software version.) Use the table below to determine the firmware requirement for your instrument.

Software Version	Compatible Models	Required Firmware
Lumic 1.0	30, 30-4, 30-6, 30-7, 35, 79	2.x or lower
	3000, 3001, 3005, 3006, 3019, 3276	N34 or lower
	3002, 3277	N12 or lower
Lumic 2.0	30, 30-4, 30-6, 30-7, 35, 79	3.x or higher
	3000, 3001, 3005, 3006, 3019, 3276	N40 or higher
	3002	N20 or higher
	3003, 3014, 3078	N/A

*Note: If you purchased the original Lumic 1.0 software, you are eligible for a free copy of Lumic 2.0. Please contact your local sales representative or Ludlum Measurements to receive your copy.

To update the firmware on your instrument:

Download the appropriate instructions file (PDF) for your instrument.
IMPORTANT: The firmware update instructions are model number specific. You must use the instructions for your specific instrument model. See table below.

Model	Instructions File
30, 30-4, 30-6, 30-7, 35, 79	Lumic Firmware Update Instructions (Model 30/35/79 Series)
3000, 3001, 3002, 3005, 3006, 3019, 3276	Lumic Firmware Update Instructions (Model 3000 Series, Gen 1)
3003, 3014, 3078	Lumic Firmware Update Instructions (Model 3000 Series, Gen 2)

Download the latest Lumic Firmware Updater Software.
Determine the printed circuit board number your instrument has. To do this, you must open the instrument can and find the number on the circuit board.
Using the drop-down selectors below, select your instrument model and printed circuit board number. This will populate a list of available firmware downloads for your instrument.