(800) 622-0828 (US, CA)
(325) 235-5494
(325) 235-4672

To search products by model number, enter "m..."
(Ex: Enter "m3" to search for Model 3.)

m30-6-w-telescoping-handle--wrapped_cable_-_angle

Model 30-6

Extended Reach microR Survey Meter

Part Number: 48-4195

Features

Rugged, Low-Weight microR Survey System
Multi-Function Pole-Mounted Digital Display
Very Sensitive Plastic Scintillator Gamma Detector
Large Backlit Display with Ambient Light Sensor
Ball-Mounted Display Unit with Adjustable Viewing Angle
Adjustable Pole Length and Handle Position

The Model 30-6 is a highly sensitive gamma µR/meter with extended reach capability designed around the versatile and lightweight Model 30 digital survey meter. It incorporates a very sensitive 15.2 x 2.5 cm (6 x 1 in.) plastic scintillator detector mounted at the end of a long pole to facilitate reaching elevated areas. The pole length is adjustable from 111 to 161 cm (43.6 to 63.4 in.), with 11 different length settings.

The digital meter features a large, easily-readable LCD (liquid crystal display) and can be rotated to maximize ease of use. Three modes of operation are available: RATE, MAX, and COUNT. Measurements can be collected in two sets of units (primary and secondary) for RATE and MAX modes in µR/hr or µSv/h units. The user can switch between two sets of chosen units by pressing the Units button. The display meter body is constructed of lightweight, durable, high-impact plastic. Splash-resistant construction allows the instrument to be used in outdoor environments. Other features include an audio warning tone and an easy, intuitive, user-friendly design.

An internal switch is used to enable or disable the front-panel setup feature to protect desired settings from inadvertent modification. Setup is also available via software from Ludlum Measurements.

Specifications

Detector	EJ-212 plastic scintillator, 15.2 x 2.5 cm (6 x 1 in.) (D x L)
Sensitivity (¹³⁷Cs gamma)	Typically 150 kcpm per µSv/h (1500 cpm per µR/hr)
Energy Response	Energy dependent
LCD Display	3-digit LCD with large 13.4 mm (0.53 in.) digits, low-battery indicator, MAX, ALARM, MUTE
Backlight	Built-in ambient light sensor automatically activates low-power LED backlight, unless internal dipswitch is set to continuous-on (will reduce battery life). Alarm light intensity varies based on ambient light levels.
Range	0.00 to 20 µSv/h (0.00 to 2000 µR/hr)
Controls	OK Button: Long press powers instrument ON and OFF; Toggle click audio; Acknowledge audio alarms; Reset MAX mode; Start/Reset the COUNT time UNITS Button: Long press cycles through configured display units. Two sets of units can be configured for RATE/MAX mode and COUNT. MODE Buttton: Long press cycles through the operating modes: RATE, MAX, COUNT
Linearity	Reading ± 10% of actual value
Response Time	User-selectable from 1 to 60 seconds, auto-response rate FAST or SLOW, or Fixed FAST and SLOW
Alarms	Count rate, exposure/dose, and count alarm setpoints adjustable over the display range
Sigma Audio Alarm	Instrument takes a baseline reading at startup. If subsequent readings exceed two sigma above baseline, a steady audio pulse pattern will sound.
Fault Detection	Overload protection, Loss of Count protection, Over-Range, Calibration Expiration Lockout
Dead Time Correction	Employs first and second order corrections for extended performance
High Voltage	700 to 1100 Vdc
Audio	Greater than 75 dB at 0.6 m (2 ft), approximately 4 kHz
Click Audio Divide	x1, x10, x100, x1k
Power	Two alkaline or two rechargeable "AAA" batteries
Battery Life	Approximately 100 hours of operation, 24-hour low battery warning
Construction	Display: High-impact plastic housing with water-resistant rubber seals Detector Housing and Pole: Aluminum with powder-coat finish
Temperature Range	-20 to 50 °C (-4 to 122 °F) May be certified for operation from -40 to 65 °C (-40 to 150 °F)
Environmental Rating	NEMA rating of 3x or IP rating of 52 with audio hole seal option (hole seal option will reduce maximum volume by approximately 10 dB)
Overall Length	Adjustable from 111 to 161 cm (43.6 to 63.4 in.), with 11 different length settings
Overall Weight	2.9 kg (6.5 lb)

Options

Option	Description	Part Number
Lumic Calibration Kit	Lumic Calibration Software allows the reading and writing of important parameters via a USB port in the Model 3000 Series and Model 30 family of instruments. This software also includes a calibration wizard (guides the user through calibration steps) and a plateau wizard (determines the optimal detector operating voltage). The kit includes Lumic Calibration Software versions 1.0 and 2.0, a Model 3000 Series USB cable, and a Model 30 family USB cable.	4519-865
Lumic Configuration Kit	Lumic Configuration Software allows the reading and writing of important parameters via a USB port in the Model 3000 Series and Model 30 family of instruments. Does not include calibration or plateau wizards. The kit includes the Lumic Configuration Software, a Model 3000 Series USB cable, and a Model 30 family USB cable.	4519-747
Headphone Jack	Adds headphone jack to instrument.	4498-697
Audio Hole Seal Option	Reduces audio volume output.	4498-913
Shoulder Strap	1.8 m (6 ft) adjustable nylon shoulder strap. Requires instrument modification.	4519-623

Firmware Updates

In order to use the latest Lumic Calibration Software*, you may need to update the firmware on your instrument. (All new instruments will be compatible with the latest software version.) Use the table below to determine the firmware requirement for your instrument.

Software Version	Compatible Models	Required Firmware
Lumic 1.0	30, 30-4, 30-6, 30-7, 35, 79	2.x or lower
	3000, 3001, 3005, 3006, 3019, 3276	N34 or lower
	3002, 3277	N12 or lower
Lumic 2.0	30, 30-4, 30-6, 30-7, 35, 79	3.x or higher
	3000, 3001, 3005, 3006, 3019, 3276	N40 or higher
	3002	N20 or higher
	3003, 3014, 3078	N/A

*Note: If you purchased the original Lumic 1.0 software, you are eligible for a free copy of Lumic 2.0. Please contact your local sales representative or Ludlum Measurements to receive your copy.

To update the firmware on your instrument:

Download the appropriate instructions file (PDF) for your instrument.
IMPORTANT: The firmware update instructions are model number specific. You must use the instructions for your specific instrument model. See table below.

Model	Instructions File
30, 30-4, 30-6, 30-7, 35, 79	Lumic Firmware Update Instructions (Model 30/35/79 Series)
3000, 3001, 3002, 3005, 3006, 3019, 3276	Lumic Firmware Update Instructions (Model 3000 Series, Gen 1)
3003, 3014, 3078	Lumic Firmware Update Instructions (Model 3000 Series, Gen 2)

Download the latest Lumic Firmware Updater Software.
Determine the printed circuit board number your instrument has. To do this, you must open the instrument can and find the number on the circuit board.
Using the drop-down selectors below, select your instrument model and printed circuit board number. This will populate a list of available firmware downloads for your instrument.