Model 3006

Extended Reach microR Survey Meter

Part Number: 48-4284

Features

• Very Sensitive Pole-Mounted Detector
• Large, Backlit, Easy-To-Read LCD Screen
• Auto-Ranging
• Rate, Max, and Count Modes
• Splash-Resistant Construction for Outdoor Use
• All-Digital Calibration
• Lightweight but Rugged
• Simple 5-Button Interface

The Model 3006 is a portable and versatile instrument with extended reach used for gamma or X-ray radiation survey. A sensitive plastic scintillator detector is mounted at the end of a 118 cm (46.5 in.) pole for ease of use when surveying trucks, scrap metal, or other items/areas of concern. It features a large, easy-to-read LCD screen and audible alarms and is controlled using a simple five-button interface. The meter body is made of high-impact plastic and splash-resistant construction allows the instrument to be used outdoors.

Three modes of operation are available - RATE, MAX, and COUNT - which can be selected by pressing the MODE button. Measurements can be collected in two sets of units (primary and secondary) for RATE and MAX modes in cps, cpm, mR/h or µSv/h units. The user can switch between the two sets of units by pressing the UNITS button. A sigma audio mode can be enabled that allows the user to find small increases above the background radiation level. When enabled with the optional Lumic Data Logger Kit (see Options), data can be logged in any of the operational modes using the LOG button on the handle. Up to 1000 data points can be stored internally.

Instrument setup can be done either through the front-panel controls or via the Lumic Calibration Kit (see Options). The Model 3006 is shipped ready to use with batteries and a calibration certificate.

• Specifications
• Options
• Documents
• Firmware Updates

• Specifications
• Options
• Documents
• Firmware Updates

Specifications

Detector (D x L)	Plastic scintillator, 15.2 x 2.5 cm (6 x 1 in.)
Sensitivity (137Cs gamma)	Typically 150 kcpm per µSv/h (1500 cpm per µR/hr)
Energy Response	Energy dependent
Linearity	Reading ± 10% of true value
Display	3-digit auto-ranging LCD with large 20 mm (0.8 in.) digits. Units: (k)cps, (k)cpm, (µ)(m)R(/h), (µ)(m)Sv(/h). Indicators: bar graph, MAX, ALARM, USB, audio, low battery.
Detector Range	Background to 20 µSv/h (2000 µR/hr)
Backlight	Built-in ambient light sensor automatically activates low-power LED backlight, unless internal dipswitch is set to continuous-on (will reduce battery life)
User Controls	ON/OFF: Extra-long press to turn ON; short press to acknowledge alarms; extra-long press plus 3 seconds to turn OFF UNITS: Short press changes the units between count rate, dose/exposure, or disintegration, an extra-long press to change count time in COUNT mode AUDIO: Short press to adjust audio level MODE: Short press alternates between modes: RATE (displays count rate), MAX (captures peak rate), and COUNT (captures rate or dose readings for a user-selectable preset count time from 0 to 10 minutes) LOG: Short press to log current display (requires Lumic Data Logger Kit, see Options), or initiate count in COUNT mode
Data Logging	Can store up to 1000 data points internally. Requires Lumic Data Logger Kit (see Options).
Response Time	User-selectable from 1 to 60 seconds, or Auto-response rate FAST or SLOW
Alarms	Two adjustable count rate, exposure/dose, and count alarm adjustable setpoints adjustable over the display range
Sigma Audio Mode	Alarm that allows user to find small increases above the background radiation level. In this mode, the instrument measures background for 8 seconds after power-up and sets a threshold rate. The instrument will beep whenever it measures a rate that exceeds the threshold rate.
Overload Protection	High count rate saturation protection prevents false display of lower count rates. "OL" will appear on the display and an audio warning will be triggered.
Loss of Count Protection	After a user-settable time interval (default 60 seconds) of no pulses from the detector, unit will flash a zero reading and the alarm audio will be triggered
Overrange	If the reading should exceed the predefined detector range, the instrument will flash a maximum reading and trigger an audio warning.
Dead Time Correction	Employs first and second order corrections for extended performance
High Voltage	400 to 1500 Vdc
Threshold	-20 to -100 mVdc
Audio	Approximately 4.5 kHz, click audio greater than 65 dB at 0.6 m (2 ft), alarm audio greater than 72 dB
Power	4 alkaline "AA" batteries
Battery Life	Approximately 750 hours of operation (as low as 100 hours with backlight configured for continuous-on), 16-hour low battery warning
Construction	High-impact plastic with water-resistant rubber seals and separate battery compartment
Temperature Range	-20 to 50 °C (-5 to 122 °F) May be certified for operation from -40 to 65 °C (-40 to 150 °F)
Environmental Rating	NEMA rating of 5 or IP rating of 53
Overall Length	118 cm (46.5 in.)
Overall Weight	3.2 kg (7.0 lb) (without batteries)

---

Options

Option	Description	Part Number
Lumic Calibration Kit	Lumic Calibration Software allows the reading and writing of important parameters via a USB port in the Model 3000 Series and Model 30 family of instruments. This software also includes a calibration wizard (guides the user through calibration steps) and a plateau wizard (determines the optimal detector operating voltage). The kit includes Lumic Calibration Software versions 1.0 and 2.0, a Model 3000 Series USB cable, and a Model 30 family USB cable.	4519-865
Lumic Configuration Kit	Lumic Configuration Software allows the reading and writing of important parameters via a USB port in the Model 3000 Series and Model 30 family of instruments. Does not include calibration or plateau wizards. The kit includes the Lumic Configuration Software, a Model 3000 Series USB cable, and a Model 30 family USB cable.	4519-747
Lumic Data Logger Kit (Model 3000-Series)	Includes Lumic Data Logger Software and cable.	4498-1019
Headphone Jack	Adds a headphone jack to the instrument.	4498-555
Stereo/Mono Headphones	Adjustable stereo/mono headphones.	22-9313
Shoulder Strap	1.8 m (6 ft) adjustable nylon shoulder strap. Requires instrument modification.	4519-246

---

Documents

• Data Sheet
• Product Manual
• CE Certificate
• Model 3000 Series Comparison Table
• Options for Model 3000 Series

---

Firmware Updates

In order to use the latest Lumic Calibration Software*, you may need to update the firmware on your instrument. (All new instruments will be compatible with the latest software version.) Use the table below to determine the firmware requirement for your instrument.

Software Version	Compatible Models	Required Firmware
Lumic 1.0	30, 30-4, 30-6, 30-7, 35, 79	2.x or lower
	3000, 3001, 3005, 3006, 3019, 3276	N34 or lower
	3002, 3277	N12 or lower
Lumic 2.0	30, 30-4, 30-6, 30-7, 35, 79	3.x or higher
	3000, 3001, 3005, 3006, 3019, 3276	N40 or higher
	3002	N20 or higher
	3003, 3014, 3078	N/A

*Note: If you purchased the original Lumic 1.0 software, you are eligible for a free copy of Lumic 2.0. Please contact your local sales representative or Ludlum Measurements to receive your copy.

---

To update the firmware on your instrument:

1. Download the appropriate instructions file (PDF) for your instrument.
   IMPORTANT: The firmware update instructions are model number specific. You must use the instructions for your specific instrument model. See table below.
   
   

   Model	Instructions File
   30, 30-4, 30-6, 30-7, 35, 79	Lumic Firmware Update Instructions (Model 30/35/79 Series)
   3000, 3001, 3002, 3005, 3006, 3019, 3276	Lumic Firmware Update Instructions (Model 3000 Series, Gen 1)
   3003, 3014, 3078	Lumic Firmware Update Instructions (Model 3000 Series, Gen 2)

2. Download the latest Lumic Firmware Updater Software.
3. Determine the printed circuit board number your instrument has. To do this, you must open the instrument can and find the number on the circuit board.
4. Using the drop-down selectors below, select your instrument model and printed circuit board number. This will populate a list of available firmware downloads for your instrument.

---